1 - 13x18 hoop
2 - Tear-away stabilizer
3 - 10 pieces of R2 acrylic batting 17 cm x 14 cm (6.7 x 5.5 in)
4 - 1 piece of R2 acrylic batting 12 cm x 12 cm (4.7 x 4.7 in)
5 - 20 pieces of white tricoline fabric 18 cm x 15 cm (7.1 x 5.9 in)
6 - 2 pieces of white tricoline fabric 13 cm x 13 cm (5.1 x 5.1 in)
7 - Masking tape
8 - Fine-tip scissors for trimming
9 - Fine pins
10 - Bobbin with thread matching the finishing color (satin stitch)
11 - Embroidery threads

Prepare the hoop with the stabilizer

Place the FAN 1 design in the machine and run the marking stitch

Place the 17 cm x 14 cm (6.7 x 5.5 in) R2 acrylic batting and the 18 cm x 15 cm (7.1 x 5.9 in) white tricoline fabric over the marking and secure with masking tape along the edges

Take it to the machine and run the tack-down stitch. Continue on the machine and embroider the next color with white thread, then the gray thread (or the color you chose for the outline)

Remove from the machine, remove the masking tapes and trim the excess batting and fabric

Place the 18 cm x 15 cm (7.1 x 5.9 in) fabric on the back side of the hoop and secure with masking tape

Take it to the machine and run the tack-down stitch. After stitching, remove from the machine and trim the excess fabric

Change the bobbin thread to white for the finishing stitch

Take it to the machine and run the finishing stitch

Remove from the machine, take it out of the hoop and remove the stabilizer. Clean the embroidery and reserve for the next stage

Prepare the hoop with the stabilizer

Place the FAN 2 design in the machine and run the marking stitch

Place the RIGHT side of the piece made in the previous stage over the marking in the hoop. Align the seam line over the seam line and secure with pins, always placing them in the seam holes as shown in the photo

Secure with masking tape all around and remove the pins

Take it to the machine and run the tack-down stitch

Remove the masking tapes from the tack-down seam and place the ribbon on the top and bottom, as shown in the photo

Place the 17 cm x 14 cm (6.7 x 5.5 in) R2 acrylic batting and the 18 cm x 15 cm (7.1 x 5.9 in) fabric over the marking and secure with masking tape

Take it to the machine and run the tack-down stitch. Continue on the machine and embroider the next color with white thread, then the gray thread (or the color you chose for the outline)

Repeat steps 5 to 9 from Stage 01

Remove from the machine, take it out of the hoop and remove the stabilizer. Clean the embroidery

Repeat all the steps of this stage 7 more times using the same design in the machine (FAN 2) to complete 9 finished pieces

- with 3 panels

- with 4 panels

- with 5 panels – make 4 additional pieces

9 FAN PIECES COMPLETED

Prepare the hoop with the stabilizer

Place the FAN 3 design in the machine and run the marking stitch

Place the placemat over the marking in the hoop and secure it with pins in the same way as in step 03 of stage 02, on both sides as shown in the photo

Secure with masking tape along the entire length of the pieces and remove the center pins, then place two pins on the upper sides

Take it to the machine and run the tack-down stitch. After stitching, remove the center masking tapes, but keep the upper pins in place

Place the 17 cm x 14 cm (6.7 x 5.5 in) R2 acrylic batting and the 18 cm x 15 cm (7.1 x 5.9 in) fabric over the marking and secure with masking tape

Take it to the machine and run the tack-down stitch. Continue on the machine and embroider the next color with white thread, then the gray thread (or the color you chose for the outline)

Remove from the machine, remove the masking tapes and trim the excess batting and fabric

On the back side of the hoop, place the 18 cm x 15 cm (7.1 x 5.9 in) fabric and secure it with masking tape

Take it to the machine and run the tack-down stitch. After stitching, remove from the machine and trim the excess fabric

Change the bobbin thread and the top thread to white for the satin stitch finishing

Take it to the machine and run the satin stitch finishing. Remove from the machine, take it out of the hoop and remove the stabilizer. Clean the embroidery.
Reserve for the next stage

Prepare the hoop with the stabilizer

Place the CENTER design in the machine and run the marking stitch

Place the piece made in the previous stage over the circle marking in the hoop, matching the seams with the seams, and secure with pins in the seam holes as in the other stages

Secure with masking tape all around and remove the pins

Take it to the machine and run the tack-down stitch. After stitching, remove from the machine and remove the masking tapes

Place the 12 cm x 12 cm (4.7 x 4.7 in) acrylic batting and the 13 cm x 13 cm (5.1 x 5.1 in) fabric over the placemat in the hoop

Secure with masking tape all around

Place the white thread in the machine and embroider the center

Remove from the machine, remove the masking tapes and trim the excess fabric

Place the 13 cm x 13 cm (5.1 x 5.1 in) fabric on the back side of the hoop and secure with masking tape. Take it to the machine and run the tack-down stitch

After stitching, remove from the machine, remove the masking tapes and trim the excess fabric

Change the bobbin thread and the top thread to white

Take it to the machine and run the satin stitch finishing. Remove from the machine, take it out of the hoop, remove the stabilizer and clean the embroidery

"OUR BOWS ARE FINISHED"